Search scope:
排序: Display mode:
Trend prediction technology of condition maintenance for large water injection units
Xiaoli XU, Sanpeng DENG
Frontiers of Mechanical Engineering 2010, Volume 5, Issue 2, Pages 171-175 doi: 10.1007/s11465-009-0091-0
Keywords: water injection units condition-based maintenance trend prediction
Economic Development Models of Gas Condensate Reservoir
Liu Tingyuan
Strategic Study of CAE 2001, Volume 3, Issue 3, Pages 85-91
Keywords: gas condensate reservoir development model gas injection nitrogen injection water injection CO 2 injection economic
Yongtao LI, Christina L. MCCARTY, Ed J. GEORGE
Frontiers of Environmental Science & Engineering 2011, Volume 5, Issue 3, Pages 417-425 doi: 10.1007/s11783-011-0310-x
Keywords: automated solid-phase extraction programmed-temperature vaporization large-volume injection gas chromatography/mass spectrometry semi-volatile organic compounds water analysis
Discussions and practice of pressurized water injection for ultra low permeability oilfield
Zhang Hongliang
Strategic Study of CAE 2012, Volume 14, Issue 4, Pages 62-64
Keywords: pressurized waterflood passive microseismic ultra low permeable oilfield affected coefficient effective injection
Jiang Zhenhai
Strategic Study of CAE 2012, Volume 14, Issue 4, Pages 77-82
Aiming at the remaining oil distribution feature in ultrahigh waterOilfield, guided by the hydrodynamic principle, based on the practical experience and analysis of cyclic waterflooding in combination with numerical simulation, cyclic water flooding and various parameters areoptimized, and layered cross injection with changing fluid direction is adopted so as to improve the
Keywords: cyclic water flooding cyclic production method optimization parameters optimization
Three-dimensional numerical simulation for plastic injection-compression molding
Yun ZHANG, Wenjie YU, Junjie LIANG, Jianlin LANG, Dequn LI
Frontiers of Mechanical Engineering 2018, Volume 13, Issue 1, Pages 74-84 doi: 10.1007/s11465-018-0490-1
Compared with conventional injection molding, injection-compression molding can mold optical partsIn this study, a 3D simulation method was developed for injection-compression molding.in the cavity were investigated by using the proposed simulation method and compared with those of injectionpressures at different points along the flow path is complicated rather than monotonically decreased in injection
Keywords: injection-compression molding simulation injection molding melt flow cavity pressure
density measurement for plastic injection molding via ultrasonic technology
Frontiers of Mechanical Engineering 2022, Volume 17, Issue 4, doi: 10.1007/s11465-022-0714-2
Keywords: ultrasonic measurement melt density in-situ measurement injection molding
Feasibility study on hot dry rock assisted oil recovery technique
Wang Xuezhong
Strategic Study of CAE 2011, Volume 13, Issue 3, Pages 104-106
Keywords: hot fry rock assist oil recovery damage by cold water thermal heavy oil hot water injection aquathermolysis
Intelligent methods for the process parameter determination of plastic injection molding
Huang GAO, Yun ZHANG, Xundao ZHOU, Dequn LI
Frontiers of Mechanical Engineering 2018, Volume 13, Issue 1, Pages 85-95 doi: 10.1007/s11465-018-0491-0
Injection molding is one of the most widely used material processing methods in producing plasticstudies and developments of the intelligent methods applied in the process parameter determination of injection
Keywords: injection molding intelligent methods process parameters optimization
Using waterflood front monitoring to track the speed of water flow drive
Yang Zhidong,Zhou Jinyan,Chang Zhiyong,Zhang Jinrong,Han Mingyi
Strategic Study of CAE 2012, Volume 14, Issue 4, Pages 31-33
Keywords: water-flooding monitoring main direction of flooding injection control
Design and application of a novel coal-fired drum boiler using saline water in heavy oil recovery
Junping GU, Yuxin WU, Liping WU, Man ZHANG, Hairui YANG, Junfu LYU
Frontiers in Energy 2020, Volume 14, Issue 4, Pages 715-725 doi: 10.1007/s11708-020-0690-3
Keywords: drum steam injection boiler natural circulation recovery wastewater staged evaporation circulating fluidized
Frontiers in Energy 2023, Volume 17, Issue 5, Pages 678-691 doi: 10.1007/s11708-022-0859-z
Keywords: gasoline compression ignition injection strategy fuel stratification high efficiency high load
CO, N, and CO/N mixed gas injection for enhanced shale gas recovery and CO geological storage
Frontiers in Energy 2023, Volume 17, Issue 3, Pages 428-445 doi: 10.1007/s11708-023-0865-9
Keywords: shale gas gas injection competitive adsorption enhanced shale gas recovery CO2 geological
Experimental study of stratified lean burn characteristics on a dual injection gasoline engine
Chun XIA, Tingyu ZHAO, Junhua FANG, Lei ZHU, Zhen HUANG
Frontiers in Energy 2022, Volume 16, Issue 6, Pages 900-915 doi: 10.1007/s11708-021-0812-6
Keywords: dual injection stratified lean burn gasoline engine particulate matter emission combustion analysis
Thomas ELLINGHAM, Hrishikesh KHARBAS, Mihai MANITIU, Guenter SCHOLZ, Lih-Sheng TURNG
Frontiers of Mechanical Engineering 2018, Volume 13, Issue 1, Pages 96-106 doi: 10.1007/s11465-018-0498-6
A three-stage molding process involving microcellular injection molding with core retraction and anfoams of varying local densities, microstructures, and mechanical properties in the same microcellular injection
Keywords: thermoplastic polyurethane microcellular injection molding cavity expansion compressive strength hysteresis
Title Author Date Type Operation
Trend prediction technology of condition maintenance for large water injection units
Xiaoli XU, Sanpeng DENG
Journal Article
Determination of selected semi-volatile organic compounds in water using automated online solid-phaseextraction with large-volume injection/gas chromatography/mass spectrometry
Yongtao LI, Christina L. MCCARTY, Ed J. GEORGE
Journal Article
Discussions and practice of pressurized water injection for ultra low permeability oilfield
Zhang Hongliang
Journal Article
Research and practice of layered cross cyclic injectionproduction water flooding technology in ultrahigh water cut stage
Jiang Zhenhai
Journal Article
Three-dimensional numerical simulation for plastic injection-compression molding
Yun ZHANG, Wenjie YU, Junjie LIANG, Jianlin LANG, Dequn LI
Journal Article
Intelligent methods for the process parameter determination of plastic injection molding
Huang GAO, Yun ZHANG, Xundao ZHOU, Dequn LI
Journal Article
Using waterflood front monitoring to track the speed of water flow drive
Yang Zhidong,Zhou Jinyan,Chang Zhiyong,Zhang Jinrong,Han Mingyi
Journal Article
Design and application of a novel coal-fired drum boiler using saline water in heavy oil recovery
Junping GU, Yuxin WU, Liping WU, Man ZHANG, Hairui YANG, Junfu LYU
Journal Article
methodology for regulating fuel stratification and improving fuel economy of GCI mode via double main-injection
Journal Article
CO, N, and CO/N mixed gas injection for enhanced shale gas recovery and CO geological storage
Journal Article
Experimental study of stratified lean burn characteristics on a dual injection gasoline engine
Chun XIA, Tingyu ZHAO, Junhua FANG, Lei ZHU, Zhen HUANG
Journal Article